12 Volt
Overall size 100 x 100 x 22mm.
CurrentDraw @13.8volts
Stop 0.08Amps, Tail 0.01Amps
Ind 0.07Amps




12 Volt
3 year warranty
Sealed Electronicss
25cm of hardwired cable

12 Volt
Overall size 150 x 80 x 22mm.
Current draw @13.8volts
Stop 0.08Amps, Tail 0.01Amps
Ind 0.07Amps.


12 Volt
3 year warranty
Sealed Electronicss
25cm of hardwired cable

Stop / Tail / Indicator / Reflector

12V Only
Fully Waterproof - IP67
Exclusive LED Autolamps design
Fully ECE approved
Low-profile design
Tough acrylic lens
integrated reflex reflector
Twin pack - blister

Overall Size with L Bracket 110 x 65 x 47mm.
Overall Lamp Size 110 x 40 x 25mm.
Current draw @13.8volts
Red 0.05Amps
Amber 0.05Amps
White 0.05Amps.

Overall Size with L Bracket 110 x 65 x 47mm.
Overall Lamp Size 110 x 40 x 25mm.
Current draw @13.8volts
Red 0.05Amps
Amber 0.05Amps
White 0.05Amps.

Overall Size with L Bracket 110 x 65 x 47mm.
Overall Lamp Size 110 x 40 x 25mm.
Current draw @13.8volts
Red 0.05Amps
Amber 0.05Amps
White 0.05Amps.

12/24V Multivolt
Fully Waterproof
Rubber Stalk Markers..

7 x 9 Strand 0.3mm
10 Metres
European Origin
Manufactured To The Highest Standard

Load Resistors

The Dummy Load resistor is designed to be used on vehicles that have electronic components that are not LED compatible. The use of an optional load resistor simulates the current draw used by a standard direction indicator bulb and enables the flasher unit to operate correctly.

Important Notice:
Must be mounted on metal surfaces. The resistor can reach up to 170 deg C, do not mount the resistor on any surface that can melt by the heat of the resistor, this includes Plastics, Hoses or Painted Surfaces.


Correct Fitting:
Using the cable terminals supplied ensure that when the wires are connected they provide a completely waterproof connection to ensure safe operation of the vehicle. Make
sure the load resistor is secured firmly by using the screws provided to an appropriate surface. If in doubt of the correct fitting procedure of this product please consult a
qualified automotive electrician.

Load Resistors

The Dummy Load resistor is designed to be used on vehicles that have electronic components that are not LED compatible. The use of an optional load resistor simulates the current draw used by a standard direction indicator bulb and enables the flasher unit to operate correctly.

Important Notice:
Must be mounted on metal surfaces. The resistor can reach up to 170 deg C, do not mount the resistor on any surface that can melt by the heat of the resistor, this includes Plastics, Hoses or Painted Surfaces.


Correct Fitting:
Using the cable terminals supplied ensure that when the wires are connected they provide a completely waterproof connection to ensure safe operation of the vehicle. Make
sure the load resistor is secured firmly by using the screws provided to an appropriate surface. If in doubt of the correct fitting procedure of this product please consult a
qualified automotive electrician.

Lifetime Warranty


12 volt
Overall size 150 x 80 x 24mm
Current draw @13.8volts
Stop 0.15Amps
Tail 0.07Amps
Ind 0.11Amps.

Lifetime Warranty


12 volt
Overall size 150 x 80 x 24mm
Current draw @13.8volts
Stop 0.15Amps
Tail 0.07Amps
Ind 0.11Amps.

Lifetime Warranty


12 volt
Overall size 150 x 80 x 24mm
Current draw @13.8volts
Stop 0.15Amps
Tail 0.07Amps
Ind 0.11Amps.

Lifetime Warranty


12 volt
Overall size 150 x 80 x 24mm
Current draw @13.8volts
Stop 0.15Amps
Tail 0.07Amps
Ind 0.11Amps.

Fully sealed against water and dust ingress, and highly resistant to shock and vibration, this lamp is ECE approved and comes with a 5 year warranty.

Available in 12V only, the 207BARP comes with 40cm of hardwired cable and our patented push-and-seal connector, which allows this lamp to be used with our LED Lighting Harness System, or wired to existing looms as required.

12V 81mm x 81mm
ECE Approved
Fully Waterproof

12V 81mm x 81mm
ECE Approved
Fully Waterproof

12V 81mm x 81mm
ECE Approved
Fully Waterproof

12V 81mm x 81mm
ECE Approved
Fully Waterproof

Wireless, magnetic and cable free...
What makes Connix different?
It’s wireless – no need to plug in, it connects to the driver controls without those annoying wires that are always in the way. ''How does it power up?'' We hear you ask - It’s rechargeable! Charge for 4 hours for 10 hours of bright light.
It’s magnetic – Swap between vehicles and machinery in a matter of seconds, and the best bit is that you don’t need any tools to attach it.
It’s multi-functional - You can use Connix as rear lighting, indicators, brake lights or to illuminate your number plate.
It’s made for the farm – Long lasting and extremely durable we created Connix with farmers in mind.
Function: 4, Brake / Tail / Indicator / Number Plate
Volts: 12V
Contains: 1 x S.143235 x 1 LH Rear Light, 1 x S.143236 RH Rear Light & 1 x S.143237 Transmitter
Recommended for agricultural equipment using EU plug wiring configurations

Improve your Connix set with the addition of two new front lights!
Perfect for use with front tanks and other front mounted implements, simply pair up the front lights to the wireless transmitter from your existing Connix set.

Fixing: 1 Bolt
Homologated: EMC/ECE Reg 10
Volts: 10/30V
IP Rating: IP67

12-24 Volts

Rated IP67

Low Current Consumption

Polycarbonate Lens

104*95*24mm

Bolt or Screw Mounting

Front Position | Directional Indicator | Reflector

ECE Approved Reg 3 | Reg 6 | Reg 7 | Reg 10

Operating Temperature -40°C to +65°C

12/24 volts
Rated IP67
Low Current Consumption
Polycarbonate Lens
104*95*24mm
Reflector | Stop | Tail | Indicator | Number Plate
ECE Approved Reg 3 | Reg 4 | Reg 6 | Reg 7
Working Temperature: -40ºC To +65ºC

12/24 volts
Rated IP67
Low Current Consumption
Polycarbonate Lens
104*95*24mm
Reflector | Stop | Tail | Indicator | Number Plate
ECE Approved Reg 3 | Reg 4 | Reg 6 | Reg 7
Working Temperature: -40ºC To +65ºC

Size 100 x 90 x 40mm

Stop /Tail/ Indicator/ Number plate /Reflector
E Mark Approved